Take A Free API 580 Exam Practice Test -Quiz Course

1.

Deterioration susceptibility and rate can be done

 
 
 

2.

………….. Is Not A Substitute For A Process Hazards Analysis (PHA) Or HAZOP

 
 
 
 

3.

Deterioration for specific process equipment is not available, this can be sourced from

 
 
 
 

4.

Small Hole, Crack Or Rupture Are Examples Of

 
 
 

5.

Failure mode can primarily affect the

 
 
 

6.

Termination Of The Ability Of A System, Structure, Or Component To Perform Its Required Function Of Containment Of Fluid (Le Loss Of Containment).

 
 
 

7.

No deterioration was found in the inspection program but still failure can occur under the following conditions.

 
 
 

8.

Occurrence of a Particular Set of Circumstances. Is Called An

 
 
 

9.

Aqueous chloride solution is carried into a sensitized stainless steel vessel, the following cracking mechanism takes very rapidly depending on temperature.

 
 
 

10.

The Risk Assessment Programme Which Focuses On Process Unit Design And Operating Practices And Their Adequacy Given The Unit’s Current Or Anticipated Operating Conditions

 
 
 
 

11.

If operating condition have changed, deterioration rates based on inspection data from the previous operating conditions

 
 
 

12.

The Reduction in the Ability of a Component to Provide Its Intended Purpose of Containment of Fluids.

 
 
 
 

13.

Effective inspection program can be derived for RBI from

 
 
 
 

14.

RBI As An Integrated Management Tool That Complements…………….

 
 
 
 

15.

In the RBI program discrimination between equipment items on the basis of the significance of potential failures.

 
 
 
 

16.

RP 580 Significantly Targeted At The Application Of RBI In The ……………..And………….Industry

 
 
 
 

17.

Consequence side of the risk equation is normally managed by.

 
 
 
 

18.

Consequence analysis will aid in the preparation of

 
 
 

19.

The method used for consequence analysis should demonstrate the ability to provide

 
 
 

20.

Loss of containment is

 
 
 
 

21.

Which of the following measures are not covered under consequence analysis?

 
 
 
 
 

22.

The affected area in the consequence analysis is

 
 
 
 

23.

RBI program typically focuses on

 
 
 

24.

RBI program will not consider the following release of common liquids such as

 
 
 
 

25.

The main Production consequences for RBI are

 
 
 

26.

Out Come Of An Event

 
 
 

27.

Maintenance impact in RBI program will be generally be measured in monitory terms and typically includes

 
 
 

28.

The Primary Audience For RP 580 Is

 
 
 
 

29.

Risk is calculated as the product of

 
 
 

30.

Users across the world will refer for more information on Risk acceptance.

 
 
 
 

31.

Utilization of RBI Provides A Vehicle for ………………….

 
 
 
 

32.

Inspection and maintenance planning using risk assessment will follow

 
 
 
 

33.

The sensitive analysis will help in improving the risk analysis.

 
 
 

34.

The general way of communicating the risk analysis is

 
 
 

35.

RBI Requires The Commitment And Cooperation Of The

 
 
 
 

36.

Different weighting is given to consequence category than probability

 
 
 

37.

RBI Is Based On

 
 
 
 

38.

Risks that are judged acceptable during RBI analysis

 
 
 

39.

Following are the ways of risk mitigation during RBI Management

 
 
 
 

40.

RP 580 Is Intended To Promote Consistency And Quality In Identification, Assessment And Management Of Risks Pertaining To………………, Which Could Lead To……………..

 
 
 
 

41.

The Program That Is Focused On Understanding Failure Modes, Addressing The Modes And Therefore Improving The Reliability Of Equipment And Process Facilities.

 
 
 
 

42.

The Primary Work Products Of The RBI Assessment And Management Approach And Implementation Of RBI Provides

 
 
 
 

43.

The Programme That Focused On Maintaining the Mechanical Integrity of Pressure Equipment Items and Minimizing the Risk of Loss of Containment Due To Deterioration.

 
 
 
 

44.

………….. Produces Inspection And Maintenance Plans For Equipment That Should Be Implemented To Provide…………… And …………….

 
 
 
 

45.

The Following Types Of Pressurized Equipment And Associated Components Covered By RBI

 
 
 

46.

Consequence Are Always…………. For Safety Aspects

 
 
 

47.

The Event May Be

 
 
 
 

48.

An Analytical Tool That Organizes And Characterizes Potential Accidents In A Logical And Graphical Manner

 
 
 
 

Question 1 of 48

Are You Looking for Free API 580 Exam Practice Test?

Take A Free API 580 Exam Practice Test
Take A Free API 580 Exam Practice Test – Risk Based Inspection Quiz Course

If your answer is yes then you are at the right website. Here You Can Take a Free Online API 580 Practice Test and Improve Your API 580 exam Score. Here You Can Learn everything you need to know about API 580 – Risk Based Inspection Exam

We will help you to pass the API 580 Certification Exam in the first attempt —99% Guaranteed. Our expert-written API practice material covers the actual exam topics with fully explained answers.

Take unlimited free Quiz Course tests of any length. We have free new questions updated every week and you can study our material along with any other study materials.

If You Want to Buy Latest API 580 Exam Self Study Material, Please Feel Free to contact us.

Buy API 580 Exam Learning Package Study Material
IN EVERY 10 QUESTIONS 1 QUESTION COMES IN EXAM
WE HAVE LATEST API 580 Exam QUESTION BANK
Total 2000+ nos QUESTION BANK FROM THEORY TO PRACTICAL TO NUMERICALS.
Cost: $25.00
Email Us To Buy: upweld.org@gmail.com
Click Here To Contact On Whatsapp https://wa.link/4dn6ee
Ideally the only material needed for passing the examination. Free guideline during learning.
We give you a lot of additional study material Free of cost with this question bank..
Get BOTH Formats Instantly:
Online—Instant scoring, review & reporting.
Printable—Instant download.

If you want to get API 580 Training and Certification, Please feel free to contact us.

API 580-581 – Risk Based Inspection Question and Answers

Top 50 Latest API 580-581 – Risk Based Inspection Question and Answers

How can you find a reputable API-580 questions answers learning source that guarantees API-580 Risk Based Inspection success? Where do I find the API-580 exam questions?

Don’t worry, you are in the right place. We have the most up-to-date and accurate questions, Improve your API 580 exam results with the UpWed Practice Tests and Exam Question Package for Risk Based Inspection.

UpWeld Provides 100% Valid API API-580 Exam Questions and answers which can helps you to Pass Your Certification Exam in First Attempt. Our API-580 Exam Questions are with all Training study guides along with corrected answers that verified by industry, Prepare for your exam certification with our API-580 Risk Based Inspection Professional most up-to-date Q&A. API-580 questions and answers PDF is easy to read and carry solution. You can prepare your API-580 exam anywhere anytime.

Success in API-580 exam is easy with valid API-580 brain dump questions answers. Pass Individual Certification Programs certification exam in first attempt.

API 580 training and preparation with our Practice Tests and Exam Question Package will help you pass your API 580 exam on the first try. The practice package contains practice tests, exam questions, API 580 Practice Tests and Exam Question Package, Online training questions for the API 580 Exam: Risk Based Inspection
Download new API-580 pdf questions from UpWeld. API 580 exam dumps answers are verified by highly qualified API experts.

Q.1. Successful implementation of RBI will give guidelines for:

  • a. Appropriate inspection methods, extent of inspection and inspection intervals,
  • b. Suggestions for Risk mitigation activities,
  • c. Managing the residual level of risk after inspection and other mitigation actions have been implemented.
  • d. All of above

Q.2. API 580 is specifically targeted at the application of RBI for:

  • a Hydrocarbon industries Oil & Gas
  • b Chemical process industries
  • c Power plants for Electric generation
  • d Only a and b above

Q.3. The graphical representation of scenarios from initiation to potential outcome of an accident will be typically called as :

  • a Event tree
  • b Fault tree
  • c Risk tree
  • d Result tree

Q.4. API 580 does not cover RBI assessment for:

  • a Process piping
  • b Storage tanks
  • c Structural systems
  • d Pressure relief devices

Q.5. The 3 approaches in RBI are typically called

  • a Qualitative, Semi-Qualitative, Realistic
  • b Quantitative, Semi-Quantitative, Qualitative
  • c Realistic, Quantitative, Qualitative
  • d None of above

Q.6. RBI methodology can be adopted for :

  • a Entire operating unit
  • b Section of operating unit
  • c Major system or major equipment
  • d All of above

Q.7. Risk Management means:

  • a Risk mitigation only
  • b Risk mitigation and risk acceptance
  • c Risk mitigation, risk acceptance and risk communication
  • d Risk assessment, risk mitigation, risk acceptance, and risk communication.

Q.8. The term “failure” used for Failure Analysis in RBI typically means:

  • a Failure due to human error
  • b Power failure
  • c Loss of containment
  • d All of above

Q.9. “Risk driver” in RBI means

  • a An item affecting probability significantly,
  • b An item affecting consequence significantly,
  • c An item affecting the either probability or consequence or both the significantly.
  • d A rash driver driving the plant vehicle who causes significant risk to plant personnel.

Q.10. In RBI analysis ‘ ALARP’ means:

  • a Always likely and reasonably possible
  • b As large as reasonably practical
  • c As large as reasonably profitable
  • d As low as reasonably practical

Q.11. Qualitative risk analysis means

  • a A risk analysis based on Quality control plans of equipment
  • b A risk analysis that uses broad categorizations for probabilities and consequences of failure for purpose of risk ranking
  • c A risk analysis that uses NDT methods to evaluate risks
  • d A risk analysis that uses high quality data for detailed numerical analysis

Q.12. RBI typically is focused on systematic determination of _______ for risk analysis and risk ranking

  • a Absolute risk
  • b Realistic risk
  • c Relative risk
  • d Residual risk

Q.13. “ISO risk line” typically represents:

  • a Constant risk level
  • b Risk acceptable to international organization for standards
  • c Incident specific occurrence of risk level
  • d None of above

Q.14. Risk Matrix and Risk Plot are typically used for:

  • a Risk Matrix for Quantitative and Risk Plot for Qualitative analysis
  • b Risk Matrix for Qualitative and Risk Plot for Quantitative analysis
  • c Both can be used for either Quantitative or Qualitative analysis
  • d None of above are correct answers

Q15. Quantitative analysis is less precise than quantitative analysis, but less costly and faster. If your objective is to carry out screening of low risks items/equipment, which type of analysis will you choose?

  • a Qualitative
  • b Quantitative
  • c Quantitative first then Qualitative
  • d API 580 does not give any guideline

Q.16. Effective Inspection by itself can directly reduce risk.

  • (a True
  • (b Wrong

Q.17. For calculating Damage factor for thinning the term ‘age’ means:

  • a Time since installation
  • b Time since RBI study was done
  • c Time since first inspection
  • d Time since last inspection

Q. 18. For finding out damage factor based on ‘inspection Effectiveness’, we should consider

  • a All past inspections
  • b Only last inspection
  • c Only internal inspection
  • d Only external inspection

Q.19. In consequence analysis in API RBI methodology

  • a Only Area-Based Consequence methodology is used
  • b Only Financial-Based Consequence methodology is used
  • c None of above these methodologies can be used
  • d Any of these methodologies can be used

Q.20. In Quantitative analysis the probability of failure depends on

  • a Generic failure frequency only,
  • b Damage factor and generic failure frequency,
  • c Management systems factor, and generic failure frequency
  • d Generic failure frequency , damage factor and management systems factor

Q.21. Choose correct option

  • a The inspection methods will provide little information to correctly identify the true damage state or 20 40% confidence is ‘Poorly Effective’.
  • b The inspection methods that will correctly identify the true damage state in nearly every case or 80–100% confidence is ‘Highly Effective’.
  • c The inspection methods will correctly identify the true damage state about half of the time or 40–60% confidence is ‘Fairly Effective’.
  • d All of above are correct statements

Q.22. In an API RBI assessment, which components should be checked for thinning.

  • a All components should be checked for thinning
  • b 50% components should be checked for thinning
  • c Only the components with General corrosion should be checked for thinning
  • d Only the components with Localized corrosion should be checked for thinning

Q.23. If a piping circuit contains an injection point, then an adjustment factor equal to —— should be used . If a highly effective inspection for injection point circuit (according to API 570 is performed, then this adjustment factor is D.

  • a 3, 2
  • b 2, 0
  • c 3, 1
  • d 2, 1

Q.24. A vessel is in service since year 2003. It is undergoing General corrosion. Up to now, two inspections with external 30% scanning by manual UT were done, and one internal inspection with 60% examination of the surface partial internals removed accompanied by thickness measurements was done. There is no On-Line Monitoring.

The value of Art parameter is 0.20. What is the Damage Factor?

  • a 4
  • b 1
  • c 10
  • d 5

Q.25. For above vessel if corrosion was localized instead of general. Two inspections with 30% manual UT scanning, and spot thickness measurements at areas specified by a corrosion specialist were done. Also one internal inspection with 60% visual examination and spot UT measurements was done. There is no On-Line Monitoring.

The value of Art parameter is 0.20. What is the Damage Factor?

  • a 10
  • b 70
  • c 35
  • d 3

Q26. A vessel is in service since year 2003. It is undergoing Chloride stress corrosion cracking. Choose the correct answer.

  • a External Spot Radiography and Spot shear wave ultrasonic is ‘Usually Effective inspection
  • b Wet fluorescent magnetic particle testing of 100% weldments done from inside is ‘Highly Effective inspection’ .
  • c Visual inspection done from inside is ‘Fairly Effective inspection’ .
  • d None of above are correct answers

Q.27. In Chloride SCC, if cracking is known to be present then for calculating damage factor Severity Index to be used is:

  • a 1
  • b 50
  • c 500
  • d 5000

Q. 28. A Carbon steel insulated vessel is operating in marine weather . Temperature=160 deg. F. The Insulation is Fiberglass. Considering the vessel nozzles, the complexity is can be determined as ‘above average’ and the insulation condition is ‘average’ What corrosion rate is to be used for Damage Factor
calculation?

a 15.6mpy
b 12.5mpy
c 19.5mpy
d 10 mpy

Q. 29. As per API 581, Financial-Based Consequence of $ 200,000 is categorized as category ——- in consequence categories:

  • a A
  • b B
  • c C
  • d D

Q. 30. As per API 581, affected Area of 1600 sq. meters is categorized as category —-— in Area-Based Consequence.

  • a B
  • b C
  • c D
  • d E

Q.31. Logic models Event Tree and Fault tree are extensively used in :

  • a Qualitative Analysis
  • b Quantitative Analysis
  • c Used in both a and b
  • d Used in neither a or b

Q.32. “Fault Tree” represents a logical model showing

  • a Initiation of an event and its consequences
  • b Various ways which lead to the occurrence of event
  • c Faults in Design and Construction of equipment
  • d Faulty in operation and maintenance of the equipment

Q.33. Typical parameters used for assessing environmental damage are:

  • a Acres of land affected per year
  • b Miles of shoreline affected per year
  • c Number of human-use resources affected
  • d All of above

Q.34. Determining representative fluid and selecting a set of hole sizes is essential step in:

  • a Qualitative approach only
  • b Quantitative approach only
  • c Essential for both
  • d Essential for none

Q.35. In RBI consequence analysis all releases are modeled in two types, namely :

  • a Instantaneous release and continuous release
  • b Continuous release and intermittent release
  • c Intermittent release and Instantaneous release
  • d “Puff” release and Instantaneous release

Q.36. In RBI consequence analysis, if fluid inside the vessel is liquid but its boiling point is less than ambient temperature , the phase considered for consequence analysis will be taken as :

  • a Solid
  • b Liquid
  • c Gas
  • d Liquid – Gas mixture

Q. 37. Probability of leak of a flammable fluid is 0.002, probability that it will catch fire is 0.5. What is probability of fire ? ( There is no solation/detection system

  • a 50%
  • b 0.0001
  • c 0.001
  • d 2 %

Q.38. Which of the following would most unlikely result in Metallurgical deterioration

  • a HTHA
  • b Fatigue
  • c CUI
  • d Chloride SCC

Q.39. Since RBI is a proven and sound risk management principle; it does not matter if designs/installations are faulty

  • a True
  • b False
  • c Cannot say

Q. 40. Engineering judgement and experience of the analyst are most required for which type of RBI assessment

  • a Quantitative
  • b Qualitative
  • c Semi-quantitative
  • d All of above

Q.41 In POF calculations Generic Failure Frequency needs to be adjusted by using an adjustment factor which depends on the damage mechanisms that are active in a component and the type of inspection performed. This factor is called

  • a Inspection factor
  • b Component factor
  • c Safety factor
  • d Damage factor

Q.42. Identify Correct Statement

  • a Properly implemented and correctly monitored RBI generally will result in Zero Risk
  • b Properly implemented RBI will generally leave “Residual Risk “
  • c Properly implemented RBI will give guidance on inspection plan and inspection intervals.
  • d b and c above are correct statements

Q.43. Mass of fluid available for release in a pressure vessel consists of

  • a Mass of fluid in pressure vessel
  • b Mass of fluid in pressure vessel + additional mass added in 3 minutes as limited to a 203 mm [8 in.] release hole size.
  • c Inventory Group Mass
  • d Lower of b and c

Q.44. Consequence of toxic release area should take into account:

  • a Area for the personnel injury
  • b Area for component damage
  • c Total of Both a and b
  • d Lower of a and b

Q.45. Integrity operating window is:

  • a Window provided in the plant wall for operating Process valves
  • b Limits for process variables which if changed beyond limits, will affect integrity of equipment
  • c Imaginary boundary enclosing equipment that is subject to same damage mechanisms
  • d None of above

Q.46. Release hole size for rupture for consequence analysis for a 30” dia pressure vessel Is

  • a 4”,
  • b 30”,
  • c 16 “,
  • d 10”

Q.47. In RBI, Sonic and subsonic release is applicable for:

  • a Liquid Release only
  • b Vapor Release only
  • c For both type Releases
  • d For None of above releases

Q.48. In RBI API 581 Quantitative analysis, Consequences for which of the following re considered

  • a Flammable Consequences
  • b Toxic Consequences
  • c Non-Flammable Non-Toxic Consequences
  • d All of above

Q.49. The parameter Art and Severity index SVI determine the damage factors. Choose correct choice from following.

  • a Parameter Art is used for thinning and Severity index SVI for cracking
  • b parameter Art and Severity index SVI both are used for cracking
  • c parameter Art and Severity index SVI both are used for thinning
  • d Parameter Art is used for cracking and Severity index SVI for thinning

Q. 50. The lowest temperature at which a fluid mixture can ignite without a source of ignition is called

  • a Auto-Ignition Temperature
  • b Ignition Temperature
  • c Flash-point Temperature
  • d Dew-point Temperature

Here You can See The Answers Keys 

IN EVERY 10 QUESTIONS 1 QUESTION COMES IN EXAM
We have Latest API 580-581 QUESTION BANK
99% Passing Guarantee
Total 2000+ nos QUESTION BANK
Cost: USD 25
Email Us To Buy: upweld.org@gmail.com
We give you lot’s of study material Free of cost with this question bank.
To join with us on YouTube: https://www.youtube.com/channel/UC_cHBXIGOKY2bsje3Tu3KQw?sub_confirmation=1

People Search Related these keywords, all keywords are relevant to this post , We are requesting to google please select any title acording to your Search Algorithm:

API 580 Risk Based Inspection Question Bank – 50 Questions
QUIZ – API 580-581 Risk Based Inspection PDF
Risk Based Inspection (RBI) Exam Practice Questions & Dumps
Risk Based Inspection Professional (API-580) Exam
Risk Based Inspection Professional (API 580) Free Practice Test
API-580 API Real Exam Questions
api rp 580 pdf free download
api rp 581 pdf
api 581 pdf free download
difference between api 580 and 581
api-580 study guide
api 580 latest edition
risk based inspection pdf
api 580 standard
API 580 Questions and Answers
api 580 3rd edition 2021 pdf
api 581 pdf
api 581-2021 pdf free download
difference between api 580 and 581
risk based inspection example
api rbi software
API 580 Questions Question Bank
practice questions & answers risk based inspection api api-580
Try Real API-580 Exam Questions
API-580 Exam Questions and Answers
Download API-580 Exam PDF Questions Answers
API 580 Practice Tests and Exam Question Package