Take a Free ASNT NDT UT Level 3 Exam Practice Test – Quiz Course

Latest ASNT NDT Ultrasonic Method (UT) Level III Examination Questions and Answers

1.

The resonant frequency of a 2 cm (0.79 in.) thick plate of naval brass (V = 4.43 × 105 cm/s) is:

 
 
 
 

2.

The length of the near field for a 2.5 cm (1 in.) diameter, 5 MHz transducer placed in oil (V = 1.4 × 105cm/s) is approximate:

 
 
 
 

3.

In a water (VL = 1.5 × 105 cm/s) immersion test, ultrasonic energy is transmitted into steel (VT = 3.2 ×105 cm/s) at an incident angle of 14°. What is the refracted shear wave within the material?

 
 
 
 

4.

The acoustic impedance for brass (V = 4.43 × 105 cm/s, p = 8.42 gm/cm³) is:

 
 
 
 

5.

What would be the wavelength of the energy in lead (V = 2.1 × 105 cm/s) if it is tested with a 25 MHz transducer?

 
 
 
 

6.

What is the transducer half-angle beam spread of a 1.25 cm diameter, 2.25 MHz transducer in water (V = 1.5 × 105 cm/s)?

 
 
 
 

7.

In an ultrasonic test system where signal amplitudes are displayed, an advantage of a frequency-independent attenuator over a continuously variable gain control is that the:

 
 
 
 

8.

An amplifier in which received echo pulses must exceed a certain threshold voltage before they can be indicated might be used to:

 
 
 
 

9.

The output voltage from a saturated amplifier is:

 
 
 
 

10.

The transmitted pulse at the output of the pulse usually has a voltage of 100 to 1000 V, whereas the voltages of the echoes at the input of the amplifier are on the order of:

 
 
 
 

11.

The intended purpose of the adjustable calibrated attenuator of an ultrasonic instrument is to:

 
 
 
 

12.

Which of the following might result in increased transmission of ultrasound within a coarse-grained material?

 
 
 
 

13.

The term that is used to determine the relative transmittance and reflectance of ultrasonic energy at an interface is called:

 
 
 
 

14.

In a forging, discontinuities associated with nonmetallic inclusions can most accurately be described as being:

 
 
 
 

15.

The preferred method of ultrasonically inspecting a complex-shaped forging:

 
 
 
 

16.

When maximum sensitivity is required from a transducer:

 
 
 
 

17.

The sensitivity of an ultrasonic test system:

 
 
 
 

18.

The ability of a test system to separate the back surface echo and the echo from a small discontinuity just above this back surface:

 
 
 
 

19.

Transducer sensitivity is most often determined by:

 
 
 
 

20.

Side-drilled holes are frequently used as reference reflectors for:

 
 
 
 

21.

Notches provide good reference discontinuities when a UT examination is conducted to primarily detect discontinuities such as:

 
 
 
 

22.

The difference between a compression and shear wave is:

 
 
 
 

23.

The particle motion for rayleigh waves is usually described as:

 
 
 
 

24.

Based upon wave theory and ignoring attenuation losses, the echo amplitude of a finite reflector is:

 
 
 
 

25.

The rate generator in B-scan equipment will invariably be directly connected to the:

 
 
 
 

26.

In A-scan equipment, the RF pulse output voltage is normally in the range of:

 
 
 
 

27.

When contact testing, an increase in tightness of a shrink-fit to a hollow shaft will cause the ratio of the back reflection to the metal-to-metal interface reflection to:

 
 
 
 

28.

The frequency that can best distinguish the difference between a large planar discontinuity and four stacked (multiple-layered) laminations in the rolled plate is:

 
 
 
 

29.

During immersion examination, when evaluating the response from a contoured surface of a part, irrelevant indications due to the contour are most likely to appear as:

 
 
 
 

30.

The pulse applied to the electrodes of the ultrasonic transducer is:

 
 
 
 

31.

In calibrating an ultrasonic test instrument using the responses from each of the area-amplitude type reference blocks, the determination of the:

 
 
 
 

32.

Test sensitivity corrections for metal distance and discontinuity area responses are accomplished by using:

 
 
 
 

33.

The time from the start of the ultrasonic pulse until the reverberations completely decay limits the maximum usable:

 
 
 
 

34.

Rough surfaces can cause undesirable effects, which are noticeable when parts are tested ultrasonically, including:

 
 
 
 

35.

Rough surfaces cause the echo amplitude from discontinuities within the part to:

 
 
 
 

36.

Resonance testing equipment generally uses:

 
 
 
 

37.

To eliminate the decrease of sensitivity close to a wall that is parallel to the beam direction, the transducer used should be:

 
 
 
 

38.

Which of the following transducer materials makes the best transmitter?

 
 
 
 

39.

Of the transducer materials listed below, the most efficient receiver is:

 
 
 
 

40.

The concentration of energy in the far-field of a transducer beam is:

 
 
 
 

41.

An extensive application of shear waves in ultrasonic testing is the inspection of:

 
 
 
 

42.

In angle beam shear wave testing, skip distance will __________ as the thickness of the test specimen is increased.

 
 
 
 

43.

The thickness range of UT resonance thickness gages can be increased by:

 
 
 
 

44.

The ability of transducers to detect echoes from small discontinuities is a definition for:

 
 
 
 

45.

From the equation for the length of the near field, it can be determined that the near field can be minimized by:

 
 
 
 

46.

The principal attributes that determine the differences in ultrasonic velocities among materials are:

 
 
 
 

47.

Wavelength may be defined as:

 
 
 
 

48.

Velocity measurements in a material revealed that the velocity decreased as frequency increased. This material is called:

 
 
 
 

49.

The sound beam emanating from a continuous wave sound source has two zones. These are called the:

 
 
 
 

50.

The difference between through-transmission and pitch-catch techniques is that:

 
 
 
 

Question 1 of 50

Are You Looking for Free ASNT NDT UT Level 3 Practice Exam Test?

Take a Free ASNT NDT UT Level 3 Exam Practice Test
Take a Free ASNT NDT UT Level 3 Exam Practice Test

If your answer is yes then you are at the right website. Here You Can Take a Free Online ASNT NDT UT Level 3 Exam Practice Test and Improve Your ASNT NDT UT Level III – Nondestructive Exam Score. Here You Can Learn everything you need to know about NDT UT Level III quick and easily.

After Compelete the last Question you will see the ASNT NDT UT Level 3 Practice Test Answer Key, No cheating now! Once you complete the test and check your answers please leave us your score and any comments in the comments section below

We will help you to pass the ASNT NDT UT Level III Exam in the first attempt —99% Guaranteed. Our expert-written ASNT NDT Ultrasonic Method UT Level III Examination practice material covers the actual exam topics with fully explained answers.

Take unlimited free ASNT NDT Ultrasonic Method UT Level 3 Quiz Course tests of any length. We have free new questions updated every week and you can study our material along with any other study materials.

If You Want to Buy Latest ASNT NDT Ultrasonic Method UT Level 3 Exam Self Study Material, Please Feel Free to contact us.

Buy ASNT NDT UT Level 3 Exam Learning Package Study Material
IN EVERY 10 QUESTIONS 1 QUESTION COMES IN EXAM
WE HAVE LATEST ASNT NDT UT Level III Exam QUESTION BANK
Total 2000+ nos QUESTION BANK FROM THEORY TO PRACTICAL TO NUMERICALS.
Cost: $25.00
Email Us To Buy: upweld.org@gmail.com
Click Here To Contact On Whatsapp https://wa.link/4dn6ee
Ideally the only material needed for passing the examination. Free guideline during learning.
We give you a lot of additional study material Free of cost with this question bank..
Get BOTH Formats Instantly:
Online—Instant scoring, review & reporting.
Printable—Instant download.

Top 85 Latest ASME Section V Questions and Answers

If you want to get ASNT NDT Ultrasonic Method UT Level 3 Training and Certification, Please feel free to contact us.