Take A Free API 1184 Exam Practice Test – Quiz Course

Here you can take free API RP 1184 Exam Practice Test with Latest Pipeline Facility Construction Inspection Multiple Choice Questions with Answers

1.

Who is considered the operator in pipeline construction?

 a) The individual responsible for quality control

 b) The regulatory agency overseeing construction

 c) The entity that operates a pipeline

 d) The contractor performing the construction

2.

What is the scope of API Recommended Practice 1184?

 a) Offshore pipeline facility construction

 b) Onshore transmission pipeline facility construction

 c) In-line inspection of pipelines

 d) Anomaly evaluation

3.

What is a permit-required confined space in pipeline construction?

 a) Any space that requires a construction permit

 b) A space that requires a special permit for access

 c) A confined space that has restricted means of entry or exit

 d) A space with limited means of entry or exit and specific hazards

4.

What is the scope of API Recommended Practice 1184?

 a) Offshore pipeline facility coaznstruction

 b) Onshore transmission pipeline facility construction

 c) In-line inspection of pipelines

 d) Anomaly evaluation

5.

Who is responsible for monitoring and inspection requirements during pipeline facility construction?

 a) Operator

 b) Contractor

 c) Regulatory agency

 d) Engineer

6.

What does AQP stand for in the context of pipeline facility construction?

 a) American Quality Plan

 b) Activity Quantity Plan

 c) Activity Quality Plan

 d) Authorized Quality Procedure

7.

What is the purpose of an activity quality plan (AQP)?

 a) To identify potential hazards

 b) To establish construction schedules

 c) To outline project budgets

 d) To identify quality concerns and control methods

8.

What is the function of chainage station numbers in pipeline construction?

 a) Measure pipeline pressure

 b) Measure pipeline flow rate

 c) Measure distance along the pipeline centerline

 d) Measure pipeline diameter

9.

What is the definition of confined space in the context of pipeline construction?

 a) Any workspace within a pipeline

 b) A space designed for continuous occupancy

 c) A tank with unrestricted entry and exit points

 d) A space with limited entry and exit points

10.

Who is considered a contractor in pipeline facility construction?

 a) Pipeline operator

 b) Regulatory agency

 c) Inspection service company

 d) Equipment supplier

11.

What is the purpose of corrective action in pipeline construction?

 a) To prevent the discovery of nonconformances

 b) To eliminate the cause of a nonconformance and prevent recurrence

 c) To increase the production speed

 d) To change the design of the pipeline facility

12.

What is a ditch plug used for in pipeline construction?

 a) To prevent erosion around the pipeline

 b) To facilitate access into a pipeline

 c) To block the flow of water in a pipeline trench

 d) To provide structural support to the pipeline

13.

What is the purpose of an exclusion zone in pipeline construction?

 a) To demarcate the construction site

 b) To establish a safe work area

 c) To mark the location of a pipeline anomaly

 d) To identify the route of the pipeline

14.

What is included within the confines of a pipeline facility, as defined by the document?

 a) Areas within a certain radius of the facility

 b) Only the compressor station of the facility

 c) Systems, equipment, and pipe located within the facility

 d) Only the storage tanks of the facility

15.

What are heritage sites in the context of pipeline facility construction?

 a) Locations of historical pipeline leaks

 b) Locations of significant equipment failures

 c) Locations of historic or cultural significance

 d) Locations of future pipeline expansions

16.

What is a holiday in the context of pipeline construction?

 a) A day when construction work is prohibited

 b) A discontinuity in a protective coating

 c) A type of pipeline anomaly

 d) A term used for pipeline corrosion

17.

What does ITP stand for in the context of pipeline construction?

 a) Inspection and Test Plan

 b) In-Transit Pipeline

 c) Inspector Training Program

 d) Inspection and Test Procedure

18.

Who is considered an inspector in pipeline facility construction?

 a) Anyone involved in construction activities

 b) A representative of the regulatory agency

 c) An individual responsible for environmental monitoring

 d) An individual qualified to monitor construction activities

19.

What is the purpose of a material test report (MTR) in pipeline construction?

 a) To document construction progress

 b) To provide weather forecasts for construction activities

 c) To indicate compliance with standards for metal products

 d) To assess the quality of welds in the pipeline

20.

What is a nonconformance in pipeline construction?

 a) A deviation from the schedule

 b) A defect that doesn’t impact safety or environment

 c) A major deviation from regulation or specification

 d) A common occurrence in construction

21.

API 1104, Welding of Pipelines and Related Facilities
What does API 1104 cover?

 a) Inspection of pipelines

 b) Welding of pipelines

 c) Construction of pipelines

 d) Maintenance of pipelines

22.

Which materials can be welded according to API 1104?

 a) Carbon and low-alloy steel only

 b) Stainless steel only

 c) Aluminum only

 d) Any type of metal

23.

Which welding processes are covered by API 1104?

 a) TIG welding only

 b) MIG welding only

 c) Multiple welding processes

 d) Plasma welding only

24.

What does “AUT” stand for in API 1104?

 a) Automated Ultrasonic Testing

 b) Arc Welding Technique

 c) Automated Underwater Testing

 d) Arc Ultrasonic Testing

25.

What is a “branch weld” according to API 1104?

 a) A completed groove weld

 b) A weld on the outside of a pipe

 c) A weld joining two fittings

 d) A weld joining a branch pipe to a run pipe

26.

What does “BT” stand for in API 1104?

 a) Butt Welding Technique

 b) Burn-Through

 c) Branch Welding Type

 d) Back Weld Test

27.

Who is responsible for conducting radiographic operations according to API 1104?

 a) Welder

 b) Radiographer

 c) Inspector

 d) Engineer

28.

What is “post weld heat treatment” (PWHT) according to API 1104?

 a) Heating a completed weld to accelerate hydrogen diffusion

 b) A repair weld made after the weld has cooled down

 c) A method to enhance the weld’s appearance

 d) Heating a completed weld to result in stress relief or other metallurgical changes

29.

What does “ICP” stand for in API 1104?

 a) International Certification Process

 b) Internal Corrosion Prevention

 c) Inadequate Cross Penetration

 d) Inspection and Control Procedure

30.

What is “porosity” in the context of welding?

 a) A type of welding process

 b) Gas trapped in the weld metal

 c) A type of filler material

 d) A type of electrode

31.

What is the purpose of “visual examination or testing” according to API 1104?

 a) To evaluate the weld’s mechanical properties

 b) To determine the cost of the welding process

 c) To detect surface discontinuities and evaluate weld acceptability

 d) To measure the heat input during welding

32.

Which term refers to welding in which the pipe is rotated while the weld metal is being deposited?

 a) Position welding

 b) Roll welding

 c) Mechanized welding

 d) Arc welding

33.

What is the main purpose of “UT qualification” according to API 1104?

 a) To test the ultrasonic equipment

 b) To evaluate the performance of welders

 c) To ensure proper equipment maintenance

 d) To evaluate the ultrasonic testing system’s accuracy

34.

Which term refers to an indication with its greatest dimension in the weld length direction?

 a) Volumetric indication

 b) Linear indication

 c) Transverse indication

 d) Radial indication

35.

What does “HVL” stand for in API 1104?

 a) High Voltage Level

 b) Heat Variability Level

 c) Half-Value Layer

 d) High Velocity Limit

36.

Which organization provides the “ISO 19232-15” standard referenced in API 1104?

 a) American Welding Society (AWS)

 b) International Organization for Standardization (ISO)

 c) NACE International

 d) British Standards Institution (BSI)

37.

Which type of welding involves mechanically controlling parameters and torch guidance?

 a) Position welding

 b) Mechanized welding

 c) Waveform-controlled welding

 d) Semiautomatic welding

38.

What is the significance of “stacked defects” in welding according to API 1104?

 a) Defects piled on top of each other

 b) A type of welding defect

 c) Weld discontinuities aligned in a specific direction

 d) Defects that have been repaired

39.

What does “EU” represent in API 1104?

 a) External Undercutting

 b) End User

 c) Erosion Undercutting

 d) Elevated Unction

40.

What is the term for a weld made to repair a defect found by visual testing?

 a) Corrective weld

 b) Secondary weld

 c) Repair weld

 d) Adaptive weld

41.

API RP 1110, Pressure Testing of Steel Pipelines for the Transportation of Gas, Petroleum Gas,
Hazardous Liquids, Highly Volatile Liquids, or Carbon Dioxide
Chapter 1: Introduction
What does API RP 1110 provide guidelines for?

 a) Pressure testing water pipelines

 b) Pressure testing steel pipelines

 c) Pressure testing pipelines for natural gas only

 d) Pressure testing pipelines for liquids only

42.

Which of the following is NOT a guiding principle of API RP 1110?

 a) Providing a consistent means of preparing and assessing pressure test results

 b) Defining specific engineering solutions

 c) Ensuring personnel safety during pressure tests

 d) Accommodating present and future pipeline technologies

43.

Chapter 2: Scope
What does “RP” stand for in API RP 1110?

 a) Recommended Procedure

 b) Regulatory Practice

 c) Recommended Practice

 d) Regulatory Procedure

44.

Which of the following is NOT covered by API RP 1110?

 a) Line pipe

 b) Control piping

 c) Valves

 d) Breakout tanks

45.

What is an “appurtenance” in the context of API RP 1110?

 a) A type of anomaly in the pipeline material

 b) A component attached to the pipeline

 c) A type of pipeline operating condition

 d) A pressure testing tool

46.

What does “SCC” stand for in the context of API RP 1110?

 a) Steel Corrosion Control

 b) Structural Component Classification

 c) Stress Corrosion Cracking

 d) Systematic Corrosion Checking

47.

Chapter 4: Pressure Test Planning Process
What is the purpose of a qualifying test?

 a) To determine if the pipeline material is suitable for use

 b) To establish the operating pressure limit of a pipeline segment

 c) To assess the level of stress corrosion cracking

 d) To measure the external corrosion rate

48.

What is the primary purpose of a spike test?

 a) To detect leaks in a pipeline

 b) To assess the level of internal corrosion

 c) To verify the structural integrity of pipelines with time-dependent anomalies

 d) To test the durability of pipeline coatings

49.

Chapter 5: Safety and Communications
What should operators consider when planning a pressure test regarding safety?

 a) Conducting the test at night to minimize risk

 b) Notifying the proper authorities and obtaining permits

 c) Skipping hazard assessments for efficiency

 d) Minimizing the use of personal protective equipment

50.

Why is communication important when planning a pressure test?

 a) To inform the public about the test

 b) To keep the test procedure a secret

 c) To avoid sharing information with contractors

 d) To ensure all parties involved are informed and aware

51.

Chapter 6: Pipeline Operating Conditions
What does MOP stand for in API RP 1110?

 a) Maximum Operating Pressure

 b) Minimum Operating Pressure

 c) Maximum Overload Pressure

 d) Minimum Overload Pressure

52.

What should the operator consider regarding pipeline operating conditions during a pressure test?

 a) The weather forecast for the test day

 b) The length of the pipeline segment being tested

 c) The maximum pressure profile during surges

 d) The proximity of water sources to the pipeline

53.

Chapter 7: Types of Pressure Tests
Which pressure test type is used to verify the structural integrity of pipelines with time-dependent anomalies?

 a) Qualifying Test

 b) Spike Test

 c) High Pressure Test

 d) Leak Test

54.

When might a high-pressure test be used?

 a) To verify the presence of leaks in the pipeline

 b) To establish the operating pressure limit of a pipeline segment

 c) To assess the level of external corrosion

 d) To determine the maximum allowable operating pressure

55.

Chapter 8: Acceptance Criteria
How is a spike test determined to be successful?

 a) If the pipeline segment being tested shows no signs of corrosion

 b) If no pipe ruptures occur during the test

 c) If the pipeline pressure drops within an acceptable range

 d) If all anomalies are repaired before the test

56.

What is the primary purpose of a leak test?

 a) To determine the level of stress corrosion cracking

 b) To assess the integrity of pipeline coatings

 c) To identify anomalies in the pipeline material

 d) To ensure the pipeline segment does not leak

57.

Chapter 9: Record Keeping
What is the purpose of keeping pressure test records according to API RP 1110?

 a) To show off to regulatory authorities

 b) To provide evidence of compliance with industry standards

 c) To fill up storage space with unnecessary documents

 d) To share with other pipeline operators for competition

58.

Who is ultimately responsible for identifying specific risks and threats for the pressure testing process?

 a) Regulatory authorities

 b) Pipeline vendors

 c) Inspection service personnel

 d) The pipeline operator

59.

Chapter 10: Conclusion
Which of the following is NOT a pipeline type covered by API RP 1110?

 a) Gas

 b) Water

 c) Hazardous liquids

 d) Carbon dioxide

60.

What is the primary purpose of API RP 1110?

 a) To provide guidelines for pressure testing water pipelines

 b) To establish regulations for pipeline construction

 c) To offer guidance for pressure testing steel pipelines

 d) To recommend materials for pipeline coatings

61.

API RP 540, Electrical Installations in Petroleum Processing Plants
Chapter 1: Introduction to Electrical Installations in Petroleum Processing Plants
What does API RP 540 provide information on?

 a) Structural design in petroleum facilities

 b) Mechanical systems in petroleum facilities

 c) Electrical installations in petroleum facilities

 d) Chemical processes in petroleum facilities

62.

Which factor necessitates the design of electrical installations to prevent accidental ignition of flammable liquids and gases in petroleum facilities?

 a) Elevated pressures

 b) High temperatures

 c) Chemical changes

 d) All of the above

63.

What is the primary focus of this recommended practice concerning electrical systems in petroleum facilities?

 a) Energy conservation

 b) Design of electrical equipment

 c) Safety and operating continuity

 d) Chemical process optimization

64.

Which type of facilities are more stringent in terms of electrical system requirements according to API RP 540?

 a) Petroleum facilities

 b) Manufacturing facilities

 c) Chemical facilities

 d) Offshore facilities

65.

What is the scope of API RP 540 limited to?

 a) Energy conservation

 b) Electrical equipment test standards

 c) Operation and maintenance

 d) Electrical installations in petroleum facilities

66.

Which aspect is addressed by API RP 540 in relation to operation and maintenance?

 a) Energy conservation techniques

 b) Electrical system design

 c) Equipment selection

 d) Safety protocols

67.

Which organization’s standards are cited in API RP 540 as references?

 a) IEEE

 b) ANSI

 c) NACE

 d) All of the above

68.

API RP 500 deals with the classification of locations for electrical installations in petroleum facilities. What is the classification based on?

 a) Ambient temperature

 b) Voltage levels

 c) Type of insulation

 d) Flammable substances presence

69.

Which standard deals with the design and installation of electrical systems for offshore production platforms?

 a) API RP 540

 b) API RP 14F

 c) IEEE Std 399

 d) NEMA MG1

70.

Which standard specifies requirements for the classification of hazardous locations based on flammable gases or vapors in petroleum facilities?

 a) API RP 505

 b) API RP 552

 c) API RP 500

 d) API RP 540

71.

What is the primary purpose of Section 2 in API RP 540?

 a) Discuss energy conservation techniques

 b) Define electrical equipment standards

 c) Review the classification of hazardous locations

 d) Address fire safety procedures

72.

Which classification system does NFPA 70 recognize for Class I locations?

 a) Division system

 b) Zone system

 c) Division and Zone systems

 d) Category system

73.

Which classification indicates that a flammable mixture may be present only in the event of abnormal operating conditions or equipment malfunction?

 a) Division 1

 b) Division 2

 c) Zone 1

 d) Zone 2

74.

According to API RP 540, where can more detailed discussions about the classification of locations be found?

 a) API RP 540

 b) NFPA 70

 c) API RP 500 and API RP 505

 d) API RP 552

75.

How are flammable gases lighter than air classified in terms of location?

 a) Class I, Division 1

 b) Zone 0

 c) Zone 2

 d) Unclassified

76.

What is the definition of a combustible liquid according to NFPA 30?

 a) Liquids with flash points below 37.8°C (100°F)

 b) Liquids with flash points at or above 37.8°C (100°F)

 c) Liquids with vapor pressures below 276 kPa at 37.8°C (100°F)

 d) Liquids with boiling points below 60°C (140°F)

77.

Which approach involves using intrinsically safe devices and wiring methods to ensure safety in classified locations?

 a) Oil immersion

 b) Nonincendive installations

 c) Positive-pressure ventilation

 d) Intrinsically safe installations

78.

What does the classification system in NFPA 70 help determine?

 a) Natural gas composition

 b) Vapor pressure of liquids

 c) Suitable electrical equipment for classified locations

 d) Combustion temperature of gases

79.

What is the primary factor that determines whether a flammable gas or vapor is ignitable in a classified location?

 a) Vapor pressure

 b) Vapor density

 c) Boiling point

 d) Mixing with air

80.

Which classification reduces the classification within an enclosure from Division 1 to unclassified through adequate positive-pressure ventilation?

 a) Type X purging

 b) Type Y purging

 c) Type Z purging

 d) Zone 1 classification

81.

API RP 686, Recommended Practice for Machinery Installation and Installation Design
Chapter 1 of API RP 686:
What is the purpose of API Recommended Practice (RP) 686?

 a) To provide vendor instructions for machinery installation

 b) To provide guidelines for equipment classification

 c) To assist with the installation design of machinery

 d) To offer contractual documents for machinery installation

82.

What is the intended scope of API 686?

 a) Automotive machinery installation

 b) Machinery installation for petrochemical facilities

 c) Machinery installation for residential buildings

 d) Machinery installation for medical facilities

83.

Which document should be followed carefully for equipment installation and checkout?

 a) API 686

 b) OEM instructions

 c) Vendor specifications

 d) Equipment user manual

84.

What is the main benefit of using API 686 as a contractual document?

 a) It reduces overall life-cycle cost

 b) It provides guidelines for machinery classification

 c) It ensures compliance with environmental regulations

 d) It eliminates the need for equipment installation

85.

When should conflicts between API 686 and manufacturers’ procedures be resolved?

 a) Before starting the installation process

 b) After the machinery has been installed

 c) During the precommissioning phase

 d) After the equipment user takes ownership

86.

What does the term “alignment” refer to?

 a) The arrangement of machinery in a facility

 b) The connection between machinery and power sources

 c) The reduction of misalignment between adjacent shafts

 d) The installation of machinery on a concrete foundation

87.

What is the purpose of an ambient offset in misalignment?

 a) To increase the efficiency of machinery

 b) To account for relative changes in shaft centerlines

 c) To provide extra clearance for machinery components

 d) To prevent angular misalignment in machinery

88.

What is a baseplate in machinery installation?

 a) A type of equipment classification

 b) A component that provides structural support

 c) A method for handling conflicting requirements

 d) A term used for machinery installation contractors

89.

What is the primary function of an oil mist console?

 a) To produce oil mist for lubrication

 b) To control the flow of gas in machinery

 c) To regulate the ambient temperature of machinery

 d) To facilitate machinery installation activities

90.

Which type of service is typically defined as critical in machinery installation?

 a) Ambient service

 b) Non-slam service

 c) Wet gas service

 d) Critical service

91.

What is the purpose of an isolation block valve?

 a) To control the flow of gas

 b) To isolate machinery for maintenance

 c) To regulate temperature in machinery

 d) To prevent equipment classification conflicts

92.

Which type of coupling obtains its flexibility from the flexing of an elastomeric element?

 a) Gear coupling

 b) Flexible-element coupling

 c) Elastomeric coupling

 d) Disk coupling

93.

What is the definition of “critical service” in machinery installation?

 a) Service with moderate importance

 b) Service with minimal downtime impact

 c) Uninterrupted, continuous operation in critical situations

 d) Routine maintenance service

94.

What is the role of a suction knockout vessel?

 a) To facilitate machinery installation

 b) To separate entrained liquid from gas

 c) To regulate machinery speed

 d) To control piping strain

95.

What is the primary goal of preliminary alignment?

 a) To achieve final alignment

 b) To ensure machinery stability

 c) To determine equipment classification

 d) To measure piping-imposed strains

96.

What is the purpose of a purge oil mist lubrication system?

 a) To lubricate machinery using mist

 b) To prevent contamination in machinery

 c) To heat up machinery components

 d) To cool down machinery bearings

97.

Which term refers to an application for which equipment is designed for uninterrupted, continuous operation in critical service?

 a) General-purpose application

 b) Ambient application

 c) Special-purpose application

 d) Wet gas application

98.

What is the function of a tabletop foundation?

 a) To connect machinery to power sources

 b) To support machinery with concrete beams

 c) To facilitate machinery transportation

 d) To control machinery vibrations

99.

What is the purpose of a warm-up line in machinery?

 a) To regulate machinery speed

 b) To heat up machinery components

 c) To measure machinery vibrations

 d) To control equipment classification

100.

What is the role of the user-designated machinery representative?

 a) To provide equipment to the vendor

 b) To speak on behalf of the equipment manufacturer

 c) To ensure proper machinery installation decisions

 d) To conduct equipment classification inspections

101.

ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes
Chapter 1: Purpose and Scope
What is the main purpose of the ANSI Z49.1 standard?

 a) To ensure efficient welding operations

 b) To provide guidelines for equipment design

 c) To protect persons and property from hazards related to welding

 d) To establish welding certification procedures

102.

Who is ANSI Z49.1 primarily intended for?

 a) Welders only

 b) Welding engineers

 c) Educators, operators, managers, and supervisors

 d) Industrial hygienists

103.

Which types of processes are covered by ANSI Z49.1?

 a) Metal fabrication processes only

 b) Welding and cutting processes only

 c) Welding, cutting, and allied processes

 d) Soldering and brazing only

104.

What is the scope of ANSI Z49.1?

 a) Guidelines for building construction

 b) Regulations for electrical installations

 c) Safe setup and use of welding equipment and operations

 d) Guidelines for equipment manufacturing

105.

Which group of people is the standard written for?

 a) Welders and shop management only

 b) Educators and engineers only

 c) Welders, shop management, educators, industrial hygienists, and engineers

 d) Welders, shop management, and engineers

106.

Chapter 1: Explanatory Requirements
What is the focus of ANSI Z49.1 in its revised versions?

 a) Building design and construction

 b) Fire and explosion prevention

 c) Control of welding and cutting operations

 d) Equipment manufacturing guidelines

107.

Which types of provisions were deleted in the revised scope of ANSI Z49.1?

 a) Safety measures for equipment manufacturing

 b) Building design and construction guidelines

 c) Facility pipelines and electrical installations

 d) Welding certification procedures

108.

Which parties can benefit from the information provided in ANSI Z49.1?

 a) Welders only

 b) Industrial hygienists only

 c) Educators, engineers, and similar responsible parties

 d) Welders and shop management only

109.

Chapter 1: Equivalency
Can systems, methods, or devices of superior quality be used instead of those prescribed by the standard?

 a) No, only standard-prescribed methods are allowed

 b) Yes, but only with prior written permission

 c) Yes, but only for welding processes

 d) No, equivalency is not permitted by the standard

110.

What needs to be submitted to demonstrate the equivalency of a system, method, or device?

 a) Certification from welding experts

 b) Technical documentation to the relevant authority

 c) A letter of intent to the standard committee

 d) Test results to the equipment manufacturer

111.

What is NOT covered by ANSI Z49.1?

 a) Equipment manufacturing guidelines

 b) Bulk gas supply systems

 c) Welding and cutting equipment

 d) Welding safety procedures

112.

Which of the following is NOT excluded from the scope of ANSI Z49.1?

 a) Building piping systems

 b) Pipeline protection systems

 c) Building electrical installations

 d) Bulk gas supply systems

113.

Who approves the system, method, or device’s equivalency for its intended purpose?

 a) Equipment manufacturer

 b) ANSI Z49.1 committee

 c) Authority having jurisdiction

 d) Industrial hygienist

114.

Chapter 1: Purpose and Scope
What is the main goal of ANSI Z49.1 regarding property protection?

 a) Preventing welding accidents

 b) Ensuring efficient welding processes

 c) Protecting equipment from damage

 d) Protecting property from fire and explosions

115.

Chapter 1: Explanatory Requirements
What types of welding processes are specifically addressed by ANSI Z49.1?

 a) Only oxyfuel gas and arc welding

 b) Oxyfuel gas, arc welding, and laser cutting

 c) Only resistance welding

 d) All types of welding processes

116.

Chapter 1: Purpose and Scope
What is the purpose of the ANSI Z49.1 standard?

 a) To promote welding as an art form

 b) To protect the environment from welding pollution

 c) To ensure proper equipment maintenance

 d) To protect individuals and property from welding hazards

117.

Chapter 1: Equivalency
What must be submitted to demonstrate the equivalency of a system, method, or device?

 a) A written request to the authorities

 b) A detailed welding procedure

 c) Technical documentation to the authority having jurisdiction

 d) A certificate from a welding inspector

118.

Chapter 1: Exclusions
Which of the following is not excluded from ANSI Z49.1?

 a) Equipment design guidelines

 b) Building piping systems

 c) Building electrical installations

 d) Bulk gas supply systems

119.

Chapter 1: Equivalency
Can systems, methods, or devices be of superior quality to the standard’s prescriptions?

 a) No, only standard-prescribed methods are allowed

 b) Yes, but without any documentation

 c) Yes, if approved by the welding manufacturer

 d) Yes, if approved by the authority having jurisdiction

120.

Chapter 1: Exclusions
Which of the following is excluded from ANSI Z49.1?

 a) Welding and cutting operations

 b) Building piping systems

 c) Bulk gas supply systems

 d) Facility pipelines

 Loading …

Question 1 of 120

Are You Looking for a Free API 1184 Exam Practice Test?

If your answer is yes, then you are on the right website. Here, you can take a free online API 1184 exam practice test to improve your API RP 1184 – Pipeline Facility Construction Inspector exam score. Here, you can learn everything you need to know about the API RP 1184 exam quickly and easily.

We will help you pass the API RP 1184 Exam on the first attempt—99% guaranteed. Our expert-written API 1184 – Pipeline Facility Construction Inspector Examination practice material covers the actual exam topics with fully explained answers.

In this free practice test, we are covering various topics related to pipeline facility construction inspection, welding of pipelines, pressure testing of pipelines for gas and liquids transportation, electrical installations in petroleum plants, machinery installation practices, safety in welding and cutting, construction safety and quality guidelines, safety orientation communication, and pipe hauling and stringing safety during construction. 

API RP 1184 Exam Syllabus:

We are covering all the topics given below in this free practice test quiz course:

• API RP 1184, Pipeline Facility Construction Inspection
• API 1104, Welding of Pipelines and Related Facilities
• API RP 1110, Pressure Testing of Steel Pipelines for the Transportation of Gas, Petroleum Gas,
• Hazardous Liquids, Highly Volatile Liquids, or Carbon Dioxide
• API RP 540, Electrical Installations in Petroleum Processing Plants
• API RP 686, Recommended Practice for Machinery Installation and Installation Design
• ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes
• INGAA Construction Safety & Quality Consensus Guidelines
• CS-G-3, Safety Orientation Communication
• CS-R-10, Pipe Hauling and Stringing Safety During Construction Activities

API RP 1184 Exam Pettron:

You’ll have three hours to finish the exam, which has 120 questions. It will be done on a computer and include 110 scored questions and 10 unscored pretest questions.

The questions in the exam can be of different types:

• Multiple-choice-single-response (MCSR): You choose the best answer from the options.
• Multiple-choice-multiple-response (MCMR): You select all the correct answers.
• Drag and drop: You match items correctly by moving them.
• Matching: You pair options from two columns.

Remember, this is a closed-book exam. You can’t use your own notes or books during the test. API won’t provide reference materials either. The questions will be based on the information from the materials listed in the publication effectiveness sheet and body of knowledge for the exam.

Take unlimited free API 1184 Exam Quiz Course tests of any length. We have free new questions updated every week, and you can study our material along with any other study materials.

Read more: Take A Free API 1169 Exam Practice Test – with the latest questions and answers

After completing the last question, you will see the API 1184 Practice Test Answer Key. No cheating now! Once you complete the test and check your answers, or also, please leave us your score and any comments in the comments section below.

If You Want to Buy the Latest API 1184 Exam Self Study Material, Please Feel Free to contact us.

If you want to get an API RP 1184 Training and Certification Course, please feel free to contact us. 

Note: If you have doubts about any question, feel free to discuss it with us.